help with 3D blade combo
2 posters
Page 1 of 1
help with 3D blade combo
Hi, my blade 7000 combo say's no signal on 3D
did a blade on line up date but no good then i tried a sky F3 box
and that works fine on 3D i'am on 2.8 did manual scan and blind,
but still no good on Blade. on T list sky box say's 12461/H/ 29499
but on blade it gives me 1246 which i scan but gets no signal
this is only on 3D, Please help
did a blade on line up date but no good then i tried a sky F3 box
and that works fine on 3D i'am on 2.8 did manual scan and blind,
but still no good on Blade. on T list sky box say's 12461/H/ 29499
but on blade it gives me 1246 which i scan but gets no signal
this is only on 3D, Please help
Gary123- Number of posts : 5
Registration date : 2013-02-04
Re: help with 3D blade combo
Works OK on Combo using 12460 (zero at the end) H 29499
Try manual scan on above,search type TV Only,does the box show red bars at the top or yellow/green.
Try manual scan on above,search type TV Only,does the box show red bars at the top or yellow/green.
jonpc- .
- Number of posts : 2835
Registration date : 2008-08-11
Re: help with 3D blade combo
Hi, tried manual scan , still no joy . red bars only at the top,
could this be a dish problem ? I am use a 1.3t, with a Black Ultre
40mm LMB . but when i put a sky F3 box on 3D works fine
could this be a dish problem ? I am use a 1.3t, with a Black Ultre
40mm LMB . but when i put a sky F3 box on 3D works fine
Gary123- Number of posts : 5
Registration date : 2013-02-04
Re: help with 3D blade combo
If it was a dish problem others channels would be affected on 28.2E.
Other channels also use 12.460 H S/R 29500,Sky Arts 1,Sky News,
try menu,OK,red button to TPs,look for 12.460 H and try other channels on that list.
Other channels also use 12.460 H S/R 29500,Sky Arts 1,Sky News,
try menu,OK,red button to TPs,look for 12.460 H and try other channels on that list.
jonpc- .
- Number of posts : 2835
Registration date : 2008-08-11
Re: help with 3D blade combo
Jut looked at the TPs not showing 12.460 H on the list,
but it is on 11.053 H , 3D, sky art's 1 Sky news, But no signal,
could it be that I have the wrong firmware , I so what f/w would you recommend? please
Thank's for all your help.
but it is on 11.053 H , 3D, sky art's 1 Sky news, But no signal,
could it be that I have the wrong firmware , I so what f/w would you recommend? please
Thank's for all your help.
Last edited by Gary123 on Tue Feb 05 2013, 14:26; edited 1 time in total (Reason for editing : ad tex)
Gary123- Number of posts : 5
Registration date : 2013-02-04
Re: help with 3D blade combo
Sky F3 being OK then the alignment on the dish is OK
Combo and dish are on wrong wavelenght.
On Combo go to dish setting, if using USALS this will help
Satellite Finder / Dish Alignment Calculator with Google Maps
Check channel TPS, http://en.kingofsat.net/
Combo and dish are on wrong wavelenght.
On Combo go to dish setting, if using USALS this will help
Satellite Finder / Dish Alignment Calculator with Google Maps
Check channel TPS, http://en.kingofsat.net/
jonpc- .
- Number of posts : 2835
Registration date : 2008-08-11
Re: help with 3D blade combo
Dish is in fixed position not motorised , Combo and dish are on wrong wavelength ? please explane
Gary123- Number of posts : 5
Registration date : 2013-02-04
Re: help with 3D blade combo
Dish is on 28E for the box to scan the correct TPs the box is not set-up with the dish,hence wrong wavelength.
Best go back to factory settings,firmware will NOT be removed,from Dooby's sticky,
To reset the box to its factory default state do the following: With the
box turned off hold the MENU button down on the front panel. Power the
box up while still holding the menu button down. You will now see the
Engineer Boot Menu. Select Option 3 to perform a factory reset on the
box. PLEASE NOTE: This will erase all user settings on the box and
return it to its factory state.
Next go to Hiteck's Sticky https://dooby2oons.forumotion.com/t2478-blade-media-7000s-stb-up-to-date-guide#13753
Forget the first part as firmware is already on box,go to
Then the no channels page will load and follow tut.
Both these stickys can be found in the Blade 7000 section
Best go back to factory settings,firmware will NOT be removed,from Dooby's sticky,
To reset the box to its factory default state do the following: With the
box turned off hold the MENU button down on the front panel. Power the
box up while still holding the menu button down. You will now see the
Engineer Boot Menu. Select Option 3 to perform a factory reset on the
box. PLEASE NOTE: This will erase all user settings on the box and
return it to its factory state.
Next go to Hiteck's Sticky https://dooby2oons.forumotion.com/t2478-blade-media-7000s-stb-up-to-date-guide#13753
Forget the first part as firmware is already on box,go to
Then the no channels page will load and follow tut.
Both these stickys can be found in the Blade 7000 section
jonpc- .
- Number of posts : 2835
Registration date : 2008-08-11
Re: help with 3D blade combo
did all that still no joy , still showing red bars on 12.460 H.
once again thank,s so much for all your help
once again thank,s so much for all your help
Gary123- Number of posts : 5
Registration date : 2013-02-04
Re: help with 3D blade combo
From your previous posts the Sky F3 works from the same dish and feed,no problem.
Factory reset as in my last post,
Then
Go to downloads and install the latest firmware for the Combo making sure not to download the Blade 7000, follow HiTecks sticky.
Factory reset as in my last post,
Then
Go to downloads and install the latest firmware for the Combo making sure not to download the Blade 7000, follow HiTecks sticky.
jonpc- .
- Number of posts : 2835
Registration date : 2008-08-11
Similar topics
» Blade combo , were can I buy one ?
» blade combo help
» blade bm7000 combo newbie ccam flash help
» Blade BM7000 Combo HD help
» blade combo streaming from pc
» blade combo help
» blade bm7000 combo newbie ccam flash help
» Blade BM7000 Combo HD help
» blade combo streaming from pc
Page 1 of 1
Permissions in this forum:
You cannot reply to topics in this forum
|
|